立式双缸液压打包机[产品打印页面]

80吨立式双缸液压打包机
 配用动力：15KW，
台时产量：3-5个包块，
包重：200-400KG，
油缸：Φ150*2支，
操作方便，机器使用68#液压油，用量120kg液压油，
 接上电源后打包 , 专用于一切轻泡、松散物料的打包。可应用于棉、羊毛、废纸、废纸箱、废纸板、纱线、塑料、布匹、编织袋、针织绒、麻、麻袋、毛条、毛球、茧、蚕丝、啤酒花、麦柴、草、废塑料袋等一切轻泡、松散物料。包型紧凑，整齐美观，可大幅降低运输成本，是棉产区、纺织企业、超市、服装厂、废旧物资回收业和其他各种轻工业企业必备的生产工具 。
80吨双缸液压打包机型号：80公称压力主缸KN：800
液体*大工作压力MPa:15
料箱尺寸长1100mm,宽700mm,高:1400mm
包块尺寸:长1100mm*宽:700 *高:(500-1000）mm
包块密度kg/m3：≥800
单次循环时间S：36
电机功率KW：15
油缸行程：1200MM
机器外形尺寸mm：长1750*宽1150*高3300。
整机重量kg；4400.
立式双缸液压打包机使用说明：
立式双缸液压打包机使用68#液压油，连接电源三相380V，额定电流为25A，安装时要有接地保护，电机要根据所示方向运转才能启用，否则不能启动。油箱加入120公斤的液压油方可启动使用。但当气温降低时液压油浓度大，机内的滤清器不能起到过滤作用，这时必须将滤清器拆出，待温度恢复后，方可生新安装使用。（注：滤清器应每月清洗1-2次）。
       溢流筏-控制该机的压力开关,旋转调压手转向右转为增压，向左转为减压，出厂前已调整好压力。但在使用过程中调压手轮可能有变位现象，导致压力升高或降低，这时需要生新调节压力，调压时应在运转中进行，同时把压板降至*低位置，调整溢流筏的调压手轮，调整压力不能高于或低于压力表所示的范围，压力的OMPA（100KG/1cm2）。旁杆-增强压的刚性和起导向作用，每次使用前应加油，起润滑作用。
      行程开关-控制该机的启动和停止的作用，因此要经常检查、维修、保养。手动转向阀-控制压板向上向下，停止的开关。
      1、手动转向阀打向下档位时压板自动向下工作，当废纸压到结实状态时，那阻力大于压力：压板不能再向下压，应把手动转向阀打向空档位置，停止加压，如果长期处于加压状态，会导致液压，电机、油泵长时间处于超负荷状态而使各机件损坏。
     2、手动转向阀打向升档位置，压板自动向上升到*高的位置，由行程开关控制自停，这时应把手动转向空档位置。完成一个工作程序。
立式双缸液压打包机使用说明书：
立式双缸液压打包机一、安装步骤
1、本机必须平稳放在混凝土上，基础视当地情况决定。
2、检查油箱底部放油口是否已关闭，确定关闭后再打开油箱顶部加油口密封盖。
注入约90KG,68#液压油，液压油排号视当地气温及使用标准决定。[注！如果机型在60T以上，新机时必须分两次注油，**次注入液压油高度至油尺顶部（蓝**线）。待压板下压至底部再加注液压油至油尺底部（红**线）详细见操作说明4]
3、安装好本机电源线,电压及频率视当地电源决定，（注！电机和电器配件的电压及频率已按客户订购机器时的要求配置安装好）常规采用三相四线制，其中三条带电源线分别接入电相内相应的三个接线位，（图7左）另一条为接地防漏电保护线，应紧接机体外露金属表面，以防电器漏电伤人。
立式双缸液压打包机操作方法：
1、通入电源：把电箱内空气开关（本机总开关）合上，先检查三相电源电压是否正常，（用仪表或探电笔测试）关闭电相门，查看电相门板表面红色电源指示灯是否亮起。
2、启动电机：把手动换向阀手柄（付图3）往下推至*底位（机体附有操作图标），然后把启动按钮NO按下（图5右下），（注：如装有急停开关机型的请把急停开关按箭头方向右旋，急停开关弹出即可），（图5右上）如正常情况下电机启动。
3、 检看电机转向：（图8）电机启动后，手动换向阀手柄在*下位时，如压板不能往下移。这时请必须立即查看电机旋转方向是否正确，电机旋转方向必须按箭头指示方向一致。如果电机转向相反时则机器不能正常使用，这时应把手动换向阀手柄往上拉至中档位。然后按下停止按钮OFF（或急停开关按下）停止电机运转。切断输入总电源，把三相电源线其中二相线互换再接上即可。再按操作1和2重新操作，（注！必须确定电机转向是否与箭头指示方向一致。）
4、注入油量的关健：当压板正常往下移时，压板在**次移动，移动速度是不均匀的。待压板移至底部或移动中突然停止又或移动中噪声加大，这种情况下应先把手动换向阀手柄往上拉?中位，把停止开关OFF或急停开关按下，停止电机运行。再仔细查看油箱储油量是否足够，如油量底于油箱高度一半时，证明油量不足，这时应再次往油箱注入适当液压油。这次加油量应加至油位尺*底界线（红**线）即可。

80 tons of vertical hydraulic balers
Waste paper baler,
 Equipped with power: 15KW,
Taiwan when the output: 3-5 mass,
Package weight: 200-400KG,
Cylinder: Φ150 * 2,
Easy to operate, the machine uses 68 # hydraulic oil, the amount of 120kg hydraulic oil,
 Connected to the power after packaging, dedicated to all light foam, loose material packaging. It can be used in cotton, wool, waste paper, waste paper box, waste paperboard, yarn, plastic, cloth, woven bag, knitted cashmere, hemp, sack, top, hair ball, cocoon, silk, hops, , Waste plastic bags and all the light foam, loose material. It is a necessary production tool for cotton producing areas, textile enterprises, supermarkets, garment factories, waste materials recycling industry and other light industrial enterprises.
80 tons of double cylinder hydraulic baler
Model: 80
Nominal pressure master cylinder KN: 800
Liquid maximum working pressure MPa: 15
Box size 1100mm long, width 700mm, height: 1400mm
Bulk size: Length 1100mm * Width: 700 * Height: (500-1000) mm
Mass density kg / m3: ≥ 800
Single cycle time S: 36
Motor power KW: 15
Cylinder travel: 1200MM
Machine dimensions mm: Length 1750 * Width 1150 * Height 3300.
Weight kg; 4400.
Instructions for use:
The factory is equipped with 68 # hydraulic oil, connected to the power supply three-phase 380V, rated current of 25A, the installation should be ground protection, the motor should be operated in accordance with the direction shown to be activated, or can not start. Fuel tank by adding 120 kg of hydraulic oil can be used to start. But when the temperature drops when the hydraulic oil concentration, the machine can not play a filter filter, then the filter must be removed until the temperature is restored before the new installation and use. (Note: the filter should be cleaned 1-2 times per month).
       Overflow raft - control the machine's pressure switch, rotary pressure hand turn right to pressurized, turn left to decompression, the factory has been adjusted before the pressure. But in the course of the use of pressure handwheel may have a displacement phenomenon, resulting in increased or decreased pressure, then need to add a new regulation of pressure, pressure should be carried out in the operation, while the pressure plate to the lowest position, adjust the overflow Rafts of the pressure regulating handwheel, the adjustment pressure can not be higher or lower than the pressure gauge shown in the range of optimum pressure for OMPA (100KG / 1cm2). Side bar - to enhance the rigidity of the pressure and play a role, each should be used before the fuel, from the lubrication.
      Stroke switch - to control the machine's start and stop the role, so often check, repair, maintenance. Manual steering valve - control the pressure plate up and down, stop the switch.
      1, manual steering valve to play down when the pressure plate automatically down work, when the waste paper to a strong state, that resistance is greater than the pressure: the pressure plate can not be pressed down, the manual steering valve should be turned to neutral position, stop Pressurized, if the long-term pressure state, will lead to hydraulic, motor, pump for a long time in a state of overload and damage to the parts.
     2, manual steering valve to the upshift position, the platen automatically rose to the highest position, controlled by the trip switch from the stop, then the manual should be turned to the neutral position. Complete a working procedure.
Hydraulic baler instructions:
First, the installation steps
1, the machine must be placed on the concrete, the basic depending on the local situation.
2, check the bottom of the fuel tank is closed, to determine the closure and then open the top of the tank filling port seal.
Injection of about 90KG, 68 # hydraulic oil, hydraulic oil row number as the local temperature and the use of standards. [Note! If the model is above 60T, the new machine must be filled with oil twice, the first time into the hydraulic oil height to the top of the dipstick (blue line). Press the press down to the bottom and then add the hydraulic oil to the bottom of the dipstick (red border) see the operating instructions in detail 4]
3, the installation of the local power cord, voltage and frequency depending on the local power supply decision, (Note! Motor and electrical parts of the voltage and frequency of customer orders have been ordered to install the machine installed) conventional three-phase four-wire system, three With the power cord, respectively, into the electrical phase of the corresponding three wiring bits (Figure 7 left) and the other for the ground leakage protection line, should be exposed to the body exposed metal surface to prevent electrical leakage wounding.
Second, the operation method:
1, access to power: the air box inside the air switch (the main switch) to close, first check the three-phase power supply voltage is normal, (with a meter or probe pen test) to close the electrical phase door, see the power of the door surface red power Whether the indicator light is on.
2, start the motor: the manual valve handle (pay Figure 3) down to the bottom (the body with the operation icon), and then press the button NO button (Figure 5 lower right), (Note: if installed There are emergency stop switch models, please put the emergency stop switch in the direction of the arrow, the emergency stop switch can pop up), (Figure 5 on the right) as normal under the motor start.
3, check the motor steering: (Figure 8) After the motor starts, manual valve handle in the lowest position, such as the pressure plate can not move down. In this case, you must immediately check whether the direction of rotation of the motor is correct and the direction of rotation of the motor must be in the direction indicated by the arrow. If the motor turns to the opposite when the machine can not be used normally, then the manual valve handle should be pulled up to the mid-range position. Then press the stop button OFF (or the emergency stop switch is pressed) to stop the motor from running. Cut off the total input power, the three-phase power cord which can be connected to the two-phase line. And then press operations 1 and 2 to re-operate, (Note! Must determine whether the motor steering direction is consistent with the arrow.)
4, into the fuel of the key: When the pressure plate down the normal move, the pressure plate in the first move, the movement speed is not uniform. To be pressed to move to the bottom or move suddenly stop or move the noise increases, in which case the manual valve should be pulled up to the middle of the handle, stop the switch OFF or emergency stop switch, stop the motor run. And then carefully check the tank oil storage is sufficient, such as oil at the end of the fuel tank height of half, to prove that the amount of oil, then again should be injected into the tank appropriate hydraulic oil. The amount of fuel should be added to the bottom line of the oil level (red line) can be.

其它液压打包机参数

机器不但外型美观，而且操作简便，耗电量小，大受客户欢迎，液压设备积累了丰富制造经验，还成为集生产、经营、设计为一体的，拥有多间分厂和三百多名精干员工，成为同行的佼佼者，使产品不仅畅销国内市场，还远销日本，香港，东南亚等地，欢迎新老客户来电或上门参观。公司拥有先进的机械加工和监测设备，有一批经验丰富具有强烈质量意识的工程技术人员以及完善的质量保证体系，这使得公司的产品受到国内外用户的一致好评。 今后，我们仍将坚持“科技**、质量**、用户至上”的经营理念，积极引进国内外先进的液压机械制造技术，创造出具有市场竞争力的高品质的液压设备，以更好地服务于我们尊敬的客户！真诚地欢迎我们的新老客户光临指导。立式液压打包机主要用于回收压缩硬纸板、废薄膜、废纸、泡沫塑料、饮料罐和工业边角料等包装材料及废品。这种立式打包机减少废物存储空间，节约达80%的堆放空间，降低运输费用，同时有利于环保和废物回收。 立式液压打包机 　　立式液压打包机主要特点 　　1.液压压实，手动装载，手动按钮操作 　　2.完全保持物料的物理特性 　　3.废料压实比可达5:1 　　4.两个捆道，方便操作 　　5.防回弹倒钩，保持压缩效果 　　6.压板自动归位 　　立式液压打包机基本结构

主要由液压缸、电机与油箱、压盘、箱体及底座、上门、下门、门闩、打包带支架、铁支等构成。 　　立式液压打包机常见故障分析 　　1 机器不能运作，但泵还在运转 　　l 马达的转动方向反了。检查马达的转动方向； 　　l 马达的电压太低以至不能在现有的负载下正常运转，检查电压； 　　l 检查液压管路是否有软管渗漏或被挟住； 　　l 检查泵耦合，确保键槽不能离开泵轴； 　　l 检查油箱中的液压油是否足够（液面应在油箱体积1/2以上的位置）； 　　l 油箱的吸滤器或顶部的透气盖可能塞住了； 　　l 检查吸引管线装置是否松了，在泵的吸引端口是否有毛细裂缝，吸引管线应该一直都有油并没有气泡； 　　2 机器运行得太慢 　　l 有东西塞住了吸滤器、透气盖或压力过滤器，或软管被挟住； 　　l 马达电压较低； 　　l 液压油较稀或较稠 　　3 马达过热 　　l 接线不正确； 　　l 由于缺油导致泵过热； 　　l 液压油太稀或太稠； 　　4 漏油或油从油箱中喷洒出来 　　透气孔阻塞导致油箱压力增大，使油喷洒出来。清理透气孔或换一个透气装置。 　　5 机器不能运作，马达不能运转 　　l 控制保险丝断了； 　　l 电机起动器超载断开。按下控制器上的“重置”按钮； 　　l 引线保险丝断了； 　　l 检查变压器； 　　l 检查按钮。

产品留言

标题

联系人

联系电话

内容

验证码

点击换一张

注：1.可以使用快捷键Alt+S或Ctrl+Enter发送信息!
2.如有必要,请您留下您的详细联系方式!